TR | EN

Şişecam Temperable Low-E Glass

Şişecam Temperable Low-E Glass is Şişecam Flat Glass’ heat control glass.

Advantages

  • Provides heat control and energy efficiency.
  • Heating expenses are reduced.
  • Do not compromise on natural daylight and transparency.
  • In accordance with architectural trends, provides solutions to safety requirements which is rising in line with expansion of the glass surface area and increase in glass thickness. It eliminates the risk of injury by dividing into small pieces which are not sharp, when breaks.
  • Reduces condensation on glass surface.
  • Ensures maximum benefit from solar heat.
  • In winter, cold spots by windows are eliminated and heat inside the room is radiated equally
Category:

Description

Şişecam Temperable Low-E Glass is Şişecam Flat Glass’ heat control glass.

Insulating Glass Unit (IGU) manufactured with Şişecam Temperable Low-E Glass reduces heat loss from windows by 50% compared to ordinary IGU and provides savings from heating expenses. Tempered heat control glass is approximately 5 times more durable than annealed heat control glass.

Colors

Besides applied on clear float glass, temperable Low-E coating can also be applied on green, gray, bronze and blue body tinted glass on demand.

Applications

Şişecam Temperable Low-E Glass is preferred in residences, office, hotel, shopping mall, airport, commercial buildings, skylights and conservatories. It provides comfortable living areas to end users with its thermal insulation property and meets safety needs when it is tempered. It is used in where transparency and low reflection are required.

Technical Specifications

Şişecam Temperable Low-E Glass is manufactured by depositing multi layered metal/metal oxides on float glass through “magnetically enhanced vacuum sputtering” technology.

“Daylight” and “Solar Energy” properties are calculated with “TNO Science and Industry – WIS 3.01” program using spectral measurements in compliance with EN 410.

“U-value” is calculated with “TNO Science and Industry – WIS 3.01” program according to EN 673. The emissivity measurements used for calculations are in compliance with EN 673 (Annex A) and EN 12898.

Thermal stresses or building codes may require the use of heat-treated glass. This document is not an evaluation of the risk of glass breakage from thermal stresses. Please contact Şişecam Flat Glass to ensure the correct form of glass to be supplied for the structure.

Specifications, technical and other data are based on information available at the time of preparation of this document and are subject to change without notice.

Trakya Cam Sanayii A.Ş. cannot be held responsible for any deviation between the data introduced and the conditions on site. This document is only informative, in no way it implies an acceptance of the order by Trakya Cam Sanayii A.Ş.

Daylight Transmittance (%): The ratio of the visible spectrum (light) that is transmitted through glass.

Daylight Reflectance (outdoor) (%): The ratio of the visible spectrum (light) that is reflected outside by glass.

Solar Factor: The percentage of total solar radiant heat energy entering the room thorough the glass. The lower solar factor means better solar control.

Shading Coefficient: The ratio of solar factor of a particular glass type to the solar factor of 3 mm clear float glass, set in identical conditions. The lower shading coefficient means better solar control.

U value (W/m2K): A measure of the rate of heat loss of a building component. The lower U value means better heat control and more comfort in winter.

Quality

Şişecam Temperable Low-E Glass is manufactured in accordance with EN 1096 Glass in Building – Coated Glass.

Thickness and Sizes

The tolerances on nominal sizes are ± 5 mm. In addition to above data, other thickness and sizes can be applied. For more information, please ask for Şişecam Flat Glass.

Processing

Temperable Low E Glass & Temperable Solar Control Low E Glass Processing

Downloads

Coated Glass Performances

Coated Glass Brochure​​

Temperable Low E Glass & Temperable Solar Control Low E Glass Processing

Related products

Our company began to operate in the architectural glass industry in the early 1970s. The founder’s profession in the retail sector continued for a period of 30 years under the name of Coskun Glass. In order to respond to developments and innovations in the sector, in 1992, Trakya Glass and Plastic Joinery Industry and Trade Inc. established and began to operate in a 5000 m2 …

TRAKYA CAM ve ALM. PLS. DOĞ. SAN.TİC.LTD.ŞTİ.

Factory 1: Namık Kemal Mahallesi 120. Sok. No: 16/B Esenyurt – Haramidere – İstanbul – Türkiye
Tel: +90 212 690 61 90 – Fax: +90 212 690 61 99
——
Factory 2: Merkez Mh. Yeni Selimpaşa San. Bölg. 6057 Sk No:5 Selimpaşa – Silivri – İstanbul – Türkiye
Tel: +90 212 734 33 23 – Fax: +90 212 734 33 26
Mail: info@trakya-cam.com.tr

TRAKYA ALM.CEPHE SİST. CAM SAN. TİC. LTD. ŞTİ

Adress: Saadetdere Mahallesi 122. Sokak No: 27/12 Esenyurt – Haramidere – İstanbul – Türkiye
Tel: +90 212 690 31 91 (Pbx)
Mail: info@trakya-cam.com.tr